Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
This article in the next paragraphs involving A Step-by-Step Guide to Installing a Bathtub is exceedingly enlightening. Check it out for yourself and figure out what you think of it.
Installing a bathtub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably difficult project. If the old bathtub is conveniently obtainable, the project can move speedily; if you need to open a wall surface to remove the old bathtub as well as position the new bath tub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will certainly need a helper to leave the old tub as well as set in the brand-new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is much better to think about employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube links.
This write-up will aid you set up a new bathtub in your shower room if you have already gotten a brand-new bathtub as well as do not require to alter the arrangement of your previous water pipelines.
Your tools and also product checklist must comprise the following:
Preparing for the Installment
To start with, the supporting frame supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to stop strain on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final placement.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you should do is separate the water supply. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bath tub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost flexible tap port to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the supply of water as well as inspect all joints as well as new pipework for leakages and tighten them if essential. Fill the tub as well as additionally examine the overflow electrical outlet and the normal outlet for leakages.
Finally, repair the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait until the bath tub has actually been used at least when as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washing machines are in location in between the tap and also the sink. Protect the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The former type ought to be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to crack a rigid seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bath tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack relatively very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly offered on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very involved in Tools You Need to Install a New Bathtub and I really hope you liked my entry. So long as you appreciated our page if you please be sure to pass it around. I am grateful for your time. Kindly pay a visit to our site back soon.
Tap leaks? Inform. Report this page